This section contains 56 1" holes per foot and is used in standard conditions where an 8" inlet is needed for capacity.
This is an 8" x 1" holed section with 8 1"x 4" slots per foot.
It is used to provide more flow than an 8" x 1" section can provide and where a 10" x 1" section is too much.
It can also be used in conjuction with an 8" restrictor to help eliminate trash build-up due to possible restriction of the 1" holes.
This is a 8" x 5/16" holed orange section used underground from the tee as a riser extension.
It can be cut at different locations (as marked on section) to adjust the height of inlet.
This is an 8" blank section and is used for offsetting the inlet from the main line.
It can also be used in place of HBI-8516 where no small holes are wanted below ground.
This section may be used horizontally or vertically.
This is an 8" new style tee which can be used to connect directly to 8" corrugated or dual wall tile.
This is an 8" x 8" x 8" wye.
Two are blind and are marked for different sizes of corrugated tile.
This is an 8" restrictor used to adjust the flow of water from the inlet to the main line.
This increaser adapts an 6" tee to a 8" riser section.
This increaser adapts a 8" tee to a 10" riser section.
This reducer adapts a 8" tee to a 6" riser section.
This reducer adapts a 10" tee to a 8" riser section.
for Hickenbottom® Inlets
8" Inlet Flowchart
General Information for Installation Practices
- Every Hickenbottom® Inlet is made of high-density polyethylene.
- All Hickenbottom® parts, tees, offsets, risers, and inlets snap together for easy installation. Risers and inlets can be cut to desired lengths.
- Markings on Hickenbottom® Inlets allow for easy height adjustment. Find the marking for the desired height and simply cut on the line.
- Hickenbottom® Inlets are lightweight and simple. There is no need to hoist in concrete catch basins and no need to weld aluminum or steel pipe inlets.
- Hickenbottom® Inlets are durable, easy to see, and easily maintained.
- Check out Hickenbottom® adapters to increase or reduce the intake of the inlet off of the inletís tee. Contact your local NRCS office to properly size restrictors for your project.
- A special inner riser may be inserted to maintain ponding at a certain level to improve water infiltration in semi-arid regions.
- Hickenbottom® Inlets are government approved. There are authorized distributors in the U.S. and Canada that have inlets in stock for fast delivery to contractors.
Installation for all Hickenbottom® Inlets should be in accordance with specifications for corrugated P.E. piping, such as ASTM F-405 and AASHTO highway specifications M-252.
These can be found in the Soil Conservation Service Engineering Field Manual for Conservation Practices in Book 2 of 2, Section 8-82 and 8-83.
When back-filling inlets at shallow depths (less than 24 inches), it is recommended that one bed the tee and underground portion of the inlet with 1/2 to 1 1/2 inches of stone aggregate (ie: limey chips).
In normal conditions concerning depths less than 24 inches (up to 72 inches), the spoil from the trench may be used for bedding if the size of the spoil material is less than 2 inches in diameter.
In conditions of 72 inches or deeper, one should surround the vertical portion of the inlet with a circumference of approximately 12 inches of the aforementioned aggregate to the surface.
To keep the vertical portion of the inlet from tipping over in the back-filling process, fill around the inlet in a mounding fashion then taper the slope down and away from the inlet to the bottom of the trench.
Make sure that all Hickenbottom® sections are snapped together before backfilling.
Further questions concerning inlet installation may be directed to the general office at 1-800-443-7879.
New Style Tee
- Although not ideal, an 8" inlet tee bell will fit the bell of 8" SDR.35 tile.
- An 8" tee bell fits over the bell of 8" Schedule 40.
- An 8" tee bell may be fitted plastic-to-plastic to a Fernco coupler (product #1056-1010).
- The spigot of an 8" stack will fit all 8" bells of Schedule 40, SDR.21, and SDR.26 as well as the inside of an 8" plastic Fernco adapter.
- Please refer to NRCS charts for further flow capacities.